ZyXEL Communications 2002 Series Uživatelská příručka Strana 33
- Strana / 161
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
VES-1000 Series Ethernet Switch
Introducing the SMT 3-1
This chapter shows you how to use the SMT (System Management Terminal) to configure a VES-1000
Series Switch.
3.1 Initial Screen
When you turn on your VES-1000 Series switch, it performs several internal tests and initializes the ports. After
the initialization, the VES-1000 Series switch asks you to press [ENTER] to continue, as shown below:
Figure 3-1 Power-On Display
3.1.1 Password
After you press [ENTER], the Login screen appears prompting you to enter the password, as shown in the next
figure.
For your first login, enter the default password “1234”. As you enter the password, the screen displays an (X) for
each character you type.
Figure 3-2 Login Screen
Please note that if there is no activity for longer than five minutes after you log in, your VES-1000 Series switch
will automatically log you out and will display a blank screen. If you see a blank screen, press [ENTER] to bring
up the password screen again.
3.2 Navigating the SMT Interface
The SMT (System Management Terminal) is the interface that you use to configure your VES-1000 Series switch.
Several operations that you should be familiar with before you attempt to modify the configuration are listed in
the following table.
Chapter 3
Introducing
the SMT
Enter Password : XXXX
Copyright (c) 2001 ZyXEL Communications Corp.
ethernet address: 00:a0:c5:00:50:02
Press ENTER to continue...
- VES-1000 Series 1
- Copyright 2
- ZyXEL Limited Warranty 3
- FCC Interference Statement 4
- FCC Warning 4
- CE Mark Warning: 4
- Taiwanese BCIQ A Warning: 4
- Certifications 4
- Customer Support 5
- Table of Contents 6
- Table of Contents vii 7
- List of Figures 9
- List of Diagrams 12
- List of Tables 13
- List of Tables xv 15
- Preface 16
- Related Documentation 17
- Getting Ready 19
- Chapter 1 21
- Switches 21
- 1.2 Applications 23
- 1.2.2 Enterprise Application 24
- 1.2.3 Campus Application 25
- Chapter 2 27
- Hardware 27
- Connections 27
- 2.3 Front Panel 28
- 2.4 Front Panel Ports 28
- 2.4.1 Console Port 29
- 2.4.2 VDSL Port Connections 29
- 2.5 Front Panel LEDs 30
- Hardware Connections 2-5 31
- Chapter 3 33
- Introducing 33
- the SMT 33
- 3.3 SMT Menus At A Glance 34
- Getting Started 38
- Chapter 4 39
- General 39
- Switch and IP Setup 39
- 4.2.1 Ethernet Port Trunking 41
- 4.2.4 GARP Timer Setup 44
- 4.2.5 GVRP 45
- 4.2.6 VLANs 45
- Port-based VLANS 46
- Tagged VLANs (IEEE 802.1Q) 46
- 4.2.7 IGMP Snooping 47
- 4.3 TCP/IP Setup 49
- Chapter 5 53
- 5.1.4 Ethernet Port Setup 56
- 5.2 Port Submenus 57
- Part III 61
- Chapter 6 63
- Route Setup 63
- 6-2 Static Route Setup 64
- Chapter 7 65
- 7.2.1 Static VLAN Setup 66
- Chapter 8 69
- Configuration 69
- 8.2 Supported MIBs 70
- 8.3 Configuring SNMP 70
- 8.4 SNMP Traps 71
- 8-4 SNMP Configuration 72
- Table 8-3 SNMP Traps 72
- System Maintenance 74
- Chapter 9 75
- Maintenance 1 75
- 9.2.1 System Maintenance 76
- Port Statistics 77
- 9-4 System Maintenance 1 78
- Table 9-2 Port Statistics 78
- System Maintenance 1 9-5 79
- 9.2.3 VLAN Status 81
- 9.3.1 System Information 83
- 9.4 Log and Trace 84
- 9.4.2 UNIX Syslog 85
- 9.5 Diagnostic 86
- System Maintenance 1 9-13 87
- Chapter 10 89
- Firmware 89
- and Configuration File 89
- Maintenance 89
- 10.2 Backup Configuration 90
- 10.2.4 GUI-based FTP Clients 92
- 10.2.7 TFTP Command Example 93
- 10.3 Restore Configuration 94
- 10.3.2 FTP Restore Example 95
- 10.4.1 Firmware File Upload 97
- 10.4.5 TFTP File Upload 99
- HyperTerminal 102
- Chapter 11 105
- Maintenance 2 105
- 11.2.1 Resetting The Time 106
- 11.3.1 Secured Client Sets 107
- 11.4 Hardware Monitor 109
- Commands 115
- Chapter 12 115
- VDSL-Related 115
- 12.2 VDSL Commands 116
- 12.2.1 Set VDSL Mode 117
- 12.2.4 Reset a VDSL Channel 118
- 12.2.7 VDSL Version Command 120
- 12.2.9 VDSL Show Command 120
- 12.2.11 VDSL Debug Command 121
- 12.3.4 Enet Fctrl Command 125
- 12.3.5 Enet Monitor Command 125
- Chapter 13 127
- Switch-Related 127
- 13.3 Port Status Command 128
- 13.4 VLANs 129
- SYMBOL DESCRIPTION 130
- 13.4.2 VLAN Set Command 131
- Sw vlan set 3 1 132
- Sw vlan set 4 1 132
- 13.4.3 VLAN Clear Command 133
- Sw vlan clear 1 3 4 134
- Sw vlan clear 1 all 134
- 13.5 MAC Address Commands 135
- 13.6 MAC Address Learning 136
- 13.6.1 MAC Address Details 137
- 13.6.2 MAC Number 137
- 13.8 Switch Driver Commands 139
- TxFreeCnt = 79287 140
- Chapter 14 141
- 14.1.2 IGMP Snooping Queries 143
- 14.1.3 Enable IGMP Snooping 143
- Chapter 15 145
- Troubleshooting 145
- 15.4 Data Rate 146
- 15.5 Configured Settings 146
- 15.6 Password 146
- 15.7 Remote Server 147
- 15.8 Telnet 147
- 15-4 Troubleshooting 148
- Appendices and Index 150
- Appendix A 151
- Hardware Specifications 151
- • 4.4 kg 152
- • 35 watts maximum 152
- • 100-240VAC/1A, 50/60Hz 152
- Appendix B 153
- Pin Assignments 153
- F Appendix B 156
Související produkty a manuály pro Sítě ZyXEL Communications 2002 Series
Sítě ZyXEL Communications G-5100 Uživatelský manuál
(18 stránky)
(18 stránky)
(140 stránky)
Sítě ZyXEL Communications M-302 Uživatelská příručka
(56 stránky)
(56 stránky)
Sítě ZyXEL Communications NSA221 Uživatelský manuál
(11 stránky)
(11 stránky)
Sítě ZyXEL Communications 10 Uživatelský manuál
(102 stránky)
(102 stránky)
Sítě ZyXEL Communications M-302 Uživatelský manuál
(14 stránky)
(14 stránky)
Sítě ZyXEL Communications MAX318M Uživatelská příručka
(102 stránky)
(102 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce