Zyxel-communications omni.net Plus Uživatelský manuál Strana 54
- Strana / 186
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Technical Reference for ZyXEL omni.net series
4-6
Manually Switching Communication Mode (for ZyXEL omni.net
LCD/LCD+M/Plus)
The manual switching functions will only be necessary if your communication software does not
allow you to change your dial-up string.
Conventional dialing commands [ATD], [ATDT] and [ATDP], used by much existing
communication software, can be mapped onto one of the new dialing commands according to the
[AT&O] setting, as follows:
For ZyXEL omni.net LCD/Plus:
Manual Switch AT Command Dial string it will map to
AT&O0
ATD, ATDT, ATDP are the same as [ATDB]
AT&O2
ATD, ATDT, ATDP are the same as [ATDI]
AT&O3
ATD, ATDT, ATDP are the same as [ATDA]
Table 22. Manual Switch AT Command For ZyXEL omni.net LCD/Plus
For ZyXEL omni.net LCD+M:
Manual Switch AT Command Dial string it will map to
AT&O0 ATD, ATDT and ATDP are the same as ATDM
AT&O1
Auto-selection of 64kbps and 3.1 kHz on outgoing
calls
AT&O2 ATD, ATDT and ATDP are the same as ATDI
AT&O3 ATD, ATDT and ATDP are the same as ATDA
Table 23. Manual Switch AT Command For ZyXEL omni.net LCD+M
(For more information on ZyXEL omni.net LCD+M, please refer to Chapter 9 Internal
Fax/Modem Function)
The factory default setting is [AT&O2] that instructs the omni.net to select ISDN data mode when
you do not otherwise specify which communication mode to use (i.e. ATD or ATDT).
- ISDN Terminal Adapters 2
- Limited Warranty 3
- Become a Registered Owner 3
- Contents 5
- PART II ISDN FUNCTION 6
- PART III VOICE FEATURES 7
- PART IV DATA FUNCTION 8
- PART V FAX/MODEM FUNCTION 9
- PART VII APPENDICES 10
- Content of Tables 13
- Content of Figures 17
- Preface 18
- How to Use This Manual 19
- Other References 19
- Part I 21
- Introduction 21
- Chapter 1 23
- Intelligent Features 24
- Specifications 24
- Key Features Summary 25
- Chapter 2 27
- ISDN Configuration Manager 27
- Bumping 31
- Configuring ISDN Parameters 32
- Chapter 3 33
- LCD/LCD+M) 33
- LCD Panel Functions 34
- Right key: 35
- Left key: 35
- Up key: 35
- Down key: 35
- Idle Screen 36
- Set Clock sub-menu 36
- Set Display Mode sub-menu 36
- Dial In Log 37
- Stored Phone List 37
- Dial Out Log 38
- Active Status 39
- Clock Options 40
- Update Clock 41
- Set Display Mode 42
- Dial In Log Options 43
- button 44
- Dial Out Log Options 45
- Part II 47
- ISDN Function 47
- Chapter 4 49
- ISDN Communication Basics 49
- Supported AT Command Types 51
- LCD/LCD+M/Plus) 54
- Placing a Data Call 55
- Incoming Calls 55
- Command Description 58
- ATS119.3=0 58
- ATS119.3=1 58
- Best effort call answering 58
- Part III 61
- Voice Features 61
- Supplementary Service 63
- Chapter 5 63
- Call Waiting 64
- Call Hold/Retrieve 64
- Three Way Conferencing 66
- Starting a conference call 66
- Call Forwarding 68
- For DSS1 switch 68
- Chapter 6 71
- Feature Phone Operation 71
- Flash Key Commands 72
- InterCom 72
- Receiving a Second Call 73
- Call Broker 74
- Call Reject 75
- Call Transfer 75
- Three-Way Conference Call 76
- Last Number Redial 77
- Quick Dial 77
- Part IV 79
- Data Function 79
- Chapter 7 81
- Feature List 82
- Async to Sync Conversion 82
- Authentication Conversion 82
- Multilink PPP 84
- Call Bumping 84
- Bandwidth On Demand (BOD) 86
- BACP/BAP 86
- Chapter 8 89
- ISDN Communications 89
- V.110 Outgoing Protocol 91
- V.120 Outgoing Protocol 92
- X.75 Outgoing Protocol 93
- Speeds of 128Kbps 95
- V.120 Bundled Call 95
- X.75 Bundled Call 97
- Table 52. V.42bis AT Command 98
- Data Compression with X.75 100
- Security Settings 101
- Modifying the User Passwords 105
- Password: 106
- Part V 107
- Fax/Modem Function 107
- Chapter 9 109
- Internal Fax/Modem Function 109
- MNP Protocols 110
- Xmodem, Ymodem, and Zmodem 110
- Fax and Facsimile 111
- Modem as a fax 111
- EIA Class 1 Fax Commands 111
- Answering a Call Using MSN 113
- Control Data Compression 115
- Fax Operation 115
- Fax Command Sets 116
- Appendix D) 118
- Part VI 119
- Diagnostics 119
- Firmware Update 119
- Chapter 10 121
- Power-on Self-test 122
- Resetting Your omni.net 124
- Capturing the Protocol Data 125
- Analyzing the Captured Data 126
- Chapter 11 129
- Firmware Upgrade 129
- Kernel Mode 130
- Part VII 133
- Appendices 133
- Appendix A 135
- AT Command Set Reference 135
- AT Commands Description 136
- AT Commands Prefix (AT) 136
- Description of ATI3 Output 144
- Fax Command 151
- Appendix B 153
- Setting S-registers 154
- S-Register Descriptions 156
- Appendix C 181
- Appendix D 183
- Serial Port Interface 183
Související produkty a manuály pro Hardware Zyxel-communications omni.net Plus
Hardware Zyxel-communications NWA3160 Uživatelský manuál
(314 stránky)
(314 stránky)
(18 stránky)
(131 stránky)
Hardware Zyxel-communications 802.11g HomePlug AV ADSL2+ Gateway P-660HWP-D1 Uživatelský manuál
(13 stránky)
(13 stránky)
Hardware Zyxel-communications NWA3550 Uživatelský manuál
(344 stránky)
(344 stránky)
Hardware Zyxel-communications NWA570N Uživatelský manuál
(152 stránky)
(152 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce