Zyxel-communications Omni 288S Uživatelský manuál Strana 25
- Strana / 136
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 2 - Installation
2-10
3. Select the following communication settings:
Setting Value
Baud rate 57,600bps
Data bits 8
Parity None
Stop bits 1
Flow control Hardware
Initialization string AT&F
Port COMn*
Note: When specifying a port assignment, the ‘n’ indicates the
computer serial port to which your modem is attached. For
example, if your modem is connected to serial port 2, you would
select COM2.
4. Place your communications software in terminal or direct connect mode
(your communications software manual will explain how).
5. Look at the modem’s front panel and verify the DTR LED is ON. If this LED
is OFF, your communications software is not addressing your modem at the
correct COM port. Make sure your software is set up for the same COM port
to which your modem is connected.
6. Type AT and press the Enter key. You should see the AT characters you
typed, followed by an OK result code. If you do not see an OK result code,
turn the modem off and on, then repeat this step. If you still cannot see the
characters, refer to Chapter 13 for troubleshooting suggestions.
7. Type ATDT number and press Enter, where number is your modem’s
telephone number. You should see a BUSY result code. If you do not see a
BUSY result code, refer to Chapter 13 for troubleshooting suggestions.
If you are not able to successfully complete this test and have already followed
the appropriate troubleshooting procedures Chapter 13, please call ZyXEL Tech
Support at 714-693-0808.
- Omni 288S 1
- User’s Manual 1
- Limited Warranty 2
- Copyright 1996 by ZyXEL 2
- Acknowledgements 2
- FCC Part 15 Information 3
- FCC Requirements 3
- Table of Contents 6
- Chapter 1 - Introduction 11
- Unpacking Your Modem 12
- Becoming a Registered Owner 13
- Omni 288S Modem Features 13
- Intelligent Features 14
- Fax Compatibility 14
- Voice Features 14
- Technical Specifications 15
- Chapter 2 - Installation 16
- Telephone Jack 17
- Microphone 17
- Windows 95 Dial-up Networking 20
- Understanding AT Commands 26
- Dialing using the ATD Command 27
- Making Your First Connection 28
- Modem Result Codes 30
- Viewing S Register Values 30
- Non-Volatile Memory 31
- Mac Serial Port 33
- Mac Software Tips 33
- Serial Cable 34
- Basic Modem Settings for UNIX 34
- Unix Software Tips 34
- Front Panel LEDs 35
- DTE Interface 36
- RS-232C or EIA-232D/E 37
- Serial RS-232C Cable 37
- Error Control 39
- Data Compression 40
- Run Length Encoding 41
- Adaptive Frequency Encoding 41
- String Coding 41
- Hardware CTS/RTS 42
- Software XON/XOFF 42
- V.25bis Command Set 43
- Clock Options 44
- RTS Options 44
- Command State Options 44
- Dialing from Synchronous Mode 45
- Leased Line Handshaking 46
- Manual Connect 47
- Auto Handshake 47
- Cellular Phone Systems 48
- Cellular Impairments 48
- ZyCellular Modes 49
- Cellular Mode Usage 50
- Office Installation 53
- Security Functions 54
- Remote Configuration 55
- Distinctive Ring 59
- Setting Up EDR 61
- EDR Application Example 62
- Chapter 9 - Fax Operation 63
- Fax Command sets 64
- Class 1 Command Set 65
- Class 2 Command Set 66
- Class 2.0 Command Set 70
- Extended Fax AT Command Set 75
- Fax Reception from a BBS 78
- Set external mail as: 79
- Voice Data Compression 80
- Voice Input/Output Devices 81
- Recording a greeting message 82
- Voice Command State 85
- Voice Data States 86
- Voice Data Reception State 86
- Event Detection and Reporting 87
- Voice AT Commands 89
- AT Command Syntax 90
- Response Syntax 90
- Flow Control 90
- ATD (with +FCLASS=8) 91
- ATH (with + FCLASS=8) 91
- AT+FCLASS=<mode> 91
- Voice Mode Action Commands 93
- AT+VTS=<string> 94
- AT+VTS=? 94
- AT+VTX 94
- AT+VGR=<gain> 95
- AT+VGR? 95
- AT+VGR=? 95
- AT+VGT=<level> 95
- AT+VLS? 97
- AT+VLS=? 97
- AT+VSD? 97
- AT+VSD=? 97
- Basic AT Command Set 99
- Description of ATI2 Output: 101
- Extended AT& Command Set 102
- Extended AT* Command Set 105
- S-Register Descriptions 107
- Result Code Options 116
- Diagnostics 118
- Resetting The Modem 119
- Loopback Tests 119
- Indicator Lights 120
- Trouble Shooting 121
- Command Echo Problems 122
- Answer Problems 123
- Dialing Problems 123
- Data Transfer Problems 123
- Connect Problems 124
- Upgrading by Flash EPROM 125
- Kernel Recovery Mode 125
- ZyXEL Phone Numbers 126
- Online Access 127
- Phone Jack Pinouts 128
- PC Serial Port Pinouts 128
- Macintosh Serial Port Pinouts 129
- Glossary 130
Související produkty a manuály pro Hardware Zyxel-communications Omni 288S
(133 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce